Tridonic Choke for 150W Metal Halides and Sons

Read more less

NiMH Battery pack 2.2 – 4.0 Ah Nickel-Metal Hydride cells (NiMH) Battery pack 2.2 Ah Battery pack 4.0 Ah Battery pack 2.2 Ah Battery pack 4.0 Ah Product description High-temperature NiMH battery pack for use with emergency lighting units 4 year design life 1 year guarantee from delivery date Properties Constant high-temperature operation Temperature depending on the used emergency lighting unit (refer to respective emergency control gear data sheet) Good charging properties at high temperature High energy maintenance of the charged battery Certified quality manufacturer Casing material made of polycarbonate 1.0 mm² stranded wire Suitable for emergency lighting equipment as per IEC 60598-2-22   Data sheet  

Read more less

2X35/49w T5 Excel ONE4ALL - Tridonic - 22185106

Read more less

15W Choke obsolete , you will be sent an 18W variant as an alternative  

Read more less

Digital Dimming Ballast to run 4 X 14/24w T5 tubes - ONE4ALL - PCA 4x14/24 T5 Excel - 22176210

Read more less

1x18w-4 TC Combo Ballast - Tridonic - PC 1x18-4 TC Combo

Read more less

The Tridonic I-SELECT 2 PLUG 400MA BL plug is a ready-to-use resistor to set output current value. This is compatible with LED drivers featuring I-Select 2 interface and is not suitable for use with first generation I-Select interface. The resistor is based isolated, has a resistor power of 0.25w and is suitable for use with LED Driver series PRE and EXC. Tridonic article number: 28001112

Read more less

I-SELECT 2 PLUG PRE / EXC Resistors for current selection Product description Ready-for-use resistor to set output current value Compatible with LED driver featuring I-select 2 interface; not compatible with I-SELECT (generation 1) Resistor is base insulated Resistor power 0.25 W Current tolerance ± 2 % additional to output current tolerance Compatible with LED driver series PRE and EXC Example of calculation R [kΩ] = 5 V / I_out [mA] x 1000 E96 resistor value used Resistor value tolerance ≤ 1 %; resistor power ≥ 0.1 W; base insulation necessary When using a resistor value beyond the specified range, the output current will automatically be set to the minimum value (resistor value too big), respectively to the maximum value (resistor value too small)

Read more less

Product description Two-colour status display LED Green: system OK, red: fault Plug connection

Read more less

Electronic ballast with highest possible energy class CELMA EEI A2 BAT. It offers large temperature range, intelligent voltage guard, precise lamp operation using adjustment of lamp parameters, advanced SMART-Heating for minimum 50000 starts without replacement of lamps, constant luminous flux irrespective of fluctuations in mains voltage, designed for THD <10%, for luminaires of protection class I and protection class II. It features automatic start after replacement of defective lamps, safety shutdown of defective lamps and at end of lamp life (EOL 2), insulation displacement connection (IDC) terminal for rapid automatic or manual wiring and for emergency lighting systems as per EN 50172. · Rated lifespan: 100,000 hours · Flicker free warm start · Min/Max ambient working temperature: -25°C to 70°C · Degree of protection: IP20 · Operating voltage: 198-264V (AC), 176-280V (DC)

Read more less

Tridonic PC118BASIC Electronic slimline ballast 1x18w TCD lamp & 1x18w TCT Lamp - Tridonic-24138832

Read more less

The Tridonic LCI 35w 1050mA TEC C LED driver is a fixed output, constant current LED driver with a maximum output power of 35w. These drivers have an average life of 50,000 hours and a 5 year guarantee. The LCI 35w 1050ma TEC has over temperature and overload protection, as well as short circuit and no-load protection. Tridonic article number: 87500198

Read more less